This is a full kit to make one Rail Humbucker pickup, suitable for the bridge position on a Telecaster®, containing everything you'll need except the copper winding wire and the hookup wire.

Please note, these are not official Fender® parts.

With tall covers and tall poles, comes increased space internally for copper - allowing you to wind a pickup to a respectable level with 42 AWG, or to use 1/4" poles with 43 AWG, or, just to go completely off the rails and design something completely unique!

Please note, these are not official Fender® parts.

Standard Lipstick neck pickup covers as seen on Telecaster® guitars. A great way to breathe a bit of life into your old guitars

Please note, these are not official Fender® parts.

This is a full kit contains everything you'll need to make a bridge pickup, which would be suitable for a Telecaster®

Please note, these are not official Fender® parts.

A pickup parts kit, fully customisable, with a selection of different magnet grades and lengths, and available with or without covers, again, in a range of finishes and materials - all ready to wind up, and drop into your favourite Telecaster, to make it truely your own.

Please note, these are not official Fender® parts.

These are the style of covers that DiMarzio® fit to their pickups designed to go into Telecaster® neck slots - slightly different to a "normal" covers because they incorporate that "triangular" shape, and flat top from a vintage cover (although the "shape" is much less angular) but the cover is more "complete", like a modern version (where the coils are completely surrounded by the cover)

Please note, these are not official DiMarzio® parts.

Sets of Alnico rod pole pole magnets.
Available for a range of different guitars and bases, in different grades of Alnico, different combinations of length, and different diameters.

These Alnico 5 pole pieces are exactly the same as we use on our single coil pickups, but we're providing them un-magnetised to allow for full customisation.

Standard Lipstick neck pickup covers as seen on Telecaster® guitars. A great way to breathe a bit of life into your old guitars. These covers have a curved top.

Please note, these are not official Fender® parts.

Standard Lipstick neck pickup covers as seen on Telecaster® guitars. A great way to breathe a bit of life into your old guitars

Please note, these are not official Fender® parts.

Open Top Lipstick pickup covers as seen on Telecaster® guitars. A great way to breathe a bit of life into your old guitars.

Please note, these are not official Fender® parts.

Standard Lipstick neck pickup covers as seen on Telecaster® guitars. A great way to breathe a bit of life into your old guitars. These covers have a flat top.

Please note, these are not official Fender® parts.

A great alternative to a pickguard, designed to mount a Telecaster® Neck Lipstick Pickup

This is a set of switch mounting and pickup height adjustment bolts for the Fender® Statocaster® and similar guitars.

Specifically, these are 6-32 UNC (imperial thread) bolts, with dome, phillips heads, with 6 "small" head screws for the pickups, and 2 larger headed versions for the switch, as well as 6 height adjustment springs.

Full Thread, Phillips, Dome head Screws used to mount a humbucker through the pickguard or mounting ring. Supplied with Springs (4)

(1)

These are the metal base plates found on most Telecaster bridge pickups - sometimes called grounding plates or Focusing plates, their primary function is to connect the strings to the ground loop of the guitar, but they do also have an effect on the pickups final tone.

Please note, these are not official Fender® parts.

These Lipstick boards are ideal for making pickups for a Telecaster® often called "flatwork" in the trade, are made to the same high standard we use on all our pickups. Constructed from Fibre board, and pre-fitted with brass eyelets for easy soldering.

Please note, these are not official Fender® parts.

These bridge boards, often called "flatwork" in the trade, are made to the same high standard we use on all our pickups and are ideal to us on Telecaster® guitars

Constructed from black Fibre board, and pre fitted with brass eyelets for easy soldering

Please note, these are not official Fender® parts.

1/2 Thread, Phillips, Dome head Screws designed to screw into a guitar body/nut and hold a pickup against its supporting springs/Foam below, or against a plate when mounted from above.

Good quality Springs to hold Pickups against pick guards reliablly, with a little bit of play.

The Fibre board used in the construction on our TT line, allowing the "rail" poles to decend below the pickup, and accomidate the bar magnet, built in the side loading style

6-32 UNC bolts usually turn up on American/Mexican/UK made instruments and parts - primarily pickups and switches, but they are becoming more common on Eastern made things too nowadays - its a little bit confusing, because theres a few different "types" (and you do get guitars that have a mix of different heads/lengths) - so as a quick, rough and ready guide.