The little plastic insert from a Trisonic, that sits above the coil and magnet, but below the cover, giving a nice, clean finish to the pickup.

These covers, are 50mm spacing, which means, when measured E to e,
center to center across the poles, that spacing, is 50mm. (actually
50.2mm, but you’ll excuse
me rounding a little).

1 x Mustang Pickup Cover

These are pickup covers designed for single coils built around 1/4" (6.35mm) poles - a bit of a niche part truth be told, and not suitable for all 1/4" single coils (because a lot of them are built with the fibre boards flush to the top of the magnets) - BUT - if your designing and winding your own pickups, and you want them to have a more "finished" look? This is the way to do it! 1/4" singles no longer have to be "rustic" looking!

These pickup covers are designed for 7 String Pickups and are available in a range of colours with 61.2mm spacing.

These covers are specifically for our Noiseless single coils and their relevant parts - taller then a normal cover to accommodate the stacked pair of coil, but, really, doing the same job as any single coil cover - just a plastic cover to protect the pickup itself.

3 x 52.5mm Pickup Covers

Single coil pickup covers, suitable for most Fender pickups, as well as DiMario, Seymour Duncan and Axesrus models - spaced 52mm center to center, to take a 5mm pole diameter.

Please note not supplied with grounding plate.

A great alternative to a pickguard for mounting single  coil pickups in a guitar with that special finish

(2)

A great alternative to a pickguard, designed to mount a Telecaster® Neck Lipstick Pickup

Standard Lipstick neck pickup covers as seen on Telecaster® guitars. A great way to breathe a bit of life into your old guitars. These covers have a flat top.

Please note, these are not official Fender® parts.

Standard Lipstick neck pickup covers as seen on Telecaster® guitars. A great way to breathe a bit of life into your old guitars

Please note, these are not official Fender® parts.

Standard Lipstick neck pickup covers as seen on Telecaster® guitars. A great way to breathe a bit of life into your old guitars. These covers have a curved top.

Please note, these are not official Fender® parts.

Please note these are not official Fender® parts.

Pickups fitted to the Fender® Jaguar®, superficially at least, look very similar to normal single coils, but one of the important components that really shape their sound, is the steel grounding plate fitted underneath the bobbin.

Please note, these are not official Fender® parts.

This is a "conversion" part - pretty straight forward really - its a humbucker ring internally, but the external "shape" is that of a Jazzmaster® pickup route.

These are the style of covers that DiMarzio® fit to their pickups designed to go into Telecaster® neck slots - slightly different to a "normal" covers because they incorporate that "triangular" shape, and flat top from a vintage cover (although the "shape" is much less angular) but the cover is more "complete", like a modern version (where the coils are completely surrounded by the cover)

Please note, these are not official DiMarzio® parts.

Covers suitable for Burns Trisonics.

Covers suitable for Burns Trisonics Bass pickups

These pickup covers are faithful reproductions of the original Single Coil covers used in the early Stratocaster® - made from Nylon rather then the PVC found on later models, and with a much softer bevel on the outside edge giving them a slightly more rounded appearance.

Standard Lipstick neck pickup covers as seen on Telecaster® guitars. A great way to breathe a bit of life into your old guitars

Please note, these are not official Fender® parts.

With tall covers and tall poles, comes increased space internally for copper - allowing you to wind a pickup to a respectable level with 42 AWG, or to use 1/4" poles with 43 AWG, or, just to go completely off the rails and design something completely unique!

Please note, these are not official Fender® parts.