These pickup covers are faithful reproductions of the original Single Coil covers used in the early Stratocaster® - made from Nylon rather then the PVC found on later models, and with a much softer bevel on the outside edge giving them a slightly more rounded appearance.

Nickel plated brass Eyelets, for fitting into pickup fiber board, giving you a point to thread the coil wire through, and to solder the hookup wires to.

This is a full kit to make one side loading single coil pickup, containing everything you'll need except the copper winding wire.

This is a full kit to make one single coil pickup, containing everything you'll need except the copper winding wire.

This is a full kit to make one single coil pickup, containing everything you'll need except the copper winding wire.

Sets of Alnico rod pole pole magnets.
Available for a range of different guitars and bases, in different grades of Alnico, different combinations of length, and different diameters.

These Alnico 5 pole pieces are exactly the same as we use on our single coil pickups, but we're providing them un-magnetised to allow for full customisation.

A great alternative to a pickguard for mounting single  coil pickups in a guitar with that special finish

(2)

Single coil pickup covers, suitable for most Fender pickups, as well as DiMario, Seymour Duncan and Axesrus models - spaced 52mm center to center, to take a 5mm pole diameter.

3 x 52.5mm Pickup Covers

This is a "very historically accurate" single coil board set, which might seem a bit of a strange thing on the face of it (how different can it actually be?!) - but there were some weird quirks in 1950s single coils that make them a little more interesting.

These Single coil boards, often called "flatwork" in the trade, are made to the same high standard we use on all our pickups. Constructed from Fibre board, and supplied with eyelets for easy soldering.

These are the fiber boards needed to make one side loading single coil - almost identical to a standard single coil, with a base, housing 2 eyelets and the threaded height adjustment holes, and a smaller top section.

These Single coil boards, often called "flatwork" in the trade, are made to the same high standard we use on all our pickups. Constructed from Fibre board, and supplied with eyelets for easy soldering.

This is a set of switch mounting and pickup height adjustment bolts for the Fender® Statocaster® and similar guitars.

Specifically, these are 6-32 UNC (imperial thread) bolts, with dome, phillips heads, with 6 "small" head screws for the pickups, and 2 larger headed versions for the switch, as well as 6 height adjustment springs.

(1)

This is a set of switch mounting and pickup height adjustment bolts for the Fender® Statocaster® and similar guitars.

Specifically, these are 6-32 UNC (imperial thread) bolts, with dome, phillips heads, with 6 "small" head screws for the pickups, and 2 larger headed versions for the switch, as well as 6 height adjustment springs.

These focusing plates are mounted to the single coil and are generally used to make them sound warmer.

Please note, these are not official Fender® parts.

Silicone tuning used on single coils, traditionally used in place of the springs (which have become much more common nowadays) - but the old silicone tubing has a bit of vintage charm about it.

These are pickup covers designed for single coils built around 1/4" (6.35mm) poles - a bit of a niche part truth be told, and not suitable for all 1/4" single coils (because a lot of them are built with the fibre boards flush to the top of the magnets) - BUT - if your designing and winding your own pickups, and you want them to have a more "finished" look? This is the way to do it! 1/4" singles no longer have to be "rustic" looking!

Good quality Springs to hold Pickups against pick guards reliablly, with a little bit of play.

These covers, are 50mm spacing, which means, when measured E to e,
center to center across the poles, that spacing, is 50mm. (actually
50.2mm, but you’ll excuse
me rounding a little).

Not exactly period correct, but very simple to use, and a much more stable base the the historic method

6-32 UNC bolts usually turn up on American/Mexican/UK made instruments and parts - primarily pickups and switches, but they are becoming more common on Eastern made things too nowadays - its a little bit confusing, because theres a few different "types" (and you do get guitars that have a mix of different heads/lengths) - so as a quick, rough and ready guide.